Formula example
Formula One JQ-1 Rubber
Triphenyl Methane Triisoester 20 Chlorobenzene 80
0.3mpa / 140 °C / 0.5h, greater than 4mpa. Metal and steel \ leather, silicon steel / rubber fabric or plastic bonding.
Recipe 2 JQ-2 Adhesive 2.4-TDI 100 24# Adhesive &s Type="> Polyester 100 400# Cement 25 Acetone 100
0.2mpa/150°C/4h. Τ greater than 1.5mpa, Τ105°C greater than 1,4mpa, use the same as above.
Formula 3 JQ-3 Adhesive
Polybutylene adipate 1.0 TDI 1.13
Room temperature 24h/120 °C, a few minutes, the peel strength (pvc artificial rate) is 56-116, used for leather adhesive.
Gum formulation 101
four Group A: end of line take-hydroxyphenyl ester of acetone 100 Part B: polyester-modified TDI 10-50 solution of ethyl
0.05mpa/20°C, 120h or 100°C/2h shear strength
At
steel
FRP
Hard PVC
leather
6.5-8
5.0-6.0
6.0-7.5
5.5-7.0
>40
Bonding of metal, plastic, leather, rubber and sponge.Formula Five SO-1 Adhesive
Sesame Oil Polyester 100 pa. TDI Prepolymer 80
20°C/48h, Τ greater than 8mpa, Τps greater than 5m.
Formula 6 leather shoe adhesive TDI and prepolymer ethyl acetate 0.5kg/cm2/20°C/48h. (For leather, sponge, foam, etc.) Leather breakage (peel strength)
Formula Seven A2-1 Adhesive
Polyester 100 Adhesive &sType="> Polyester Modified TDI 500
0.5kg/CM2/60°C/5H
material
Copper
aluminum
steel
stainless steel
(mpa)
72.3
25.0
30.4
33
temperature
60
20
60
80
100
Τ(mpa)
22.8
25.0
10.3
7.5
5.3
For metals, plastics and rubber adhesive formulations eightadhesive 404 Panda Group A: sesame oil modified polyester 100
Group B: Prepolymer 70-100
0.5kg/cm2/60°C/5h
material
Al
steel
Pmma
(mpa)
6.0
5.4
5.0
Use supragum formulation nine Panda 7.7 20 ℃ / 48h, Τ = 7.1mpa , Τ steel peeling strength = 4.9 MPa (leather, rubber) = 25-80M / cm, use the same terminal isocyanate prepolymer fluoro benzene ring formulations body
ten J-38 Group A plastic
: JQ-1 adhesive 100 Group B: p-nifedipine -N, N- xylene aniline 10
At 20°C/48h, the rubber is broken at -60°C, 20°C, and 160°C under 10-6MMHG proton and electronic radiation, and used for metal and rubber bonding.
Formula 11 Panda 202 glue
A: Diphenyl methane diacrylate &s Type="> Isocyanate 15-20 B: Neoprene fluid 100 (Including ENO: MGO: Anti-aging = 5:44:2)
20°C/24h, peel strength (stainless steel/rubber) greater than 50N/cm, use the same as above.
Formula 12 cryogenic adhesive 1#
Trihydroxy Polyether prepolymer 100 3,3'-dichloro-4.4'-diaminodiphenylmethane 20
100 °C / 4h, Τ = 12mpa. Τ-196 °C = 25mpa super, low temperature parts glued.
Formula 13 cryogenic glue 2#
616# epoxy prepolymer 100 3,3'-dichloro-4,4'-diaminodiphenylmethane 20
60°C/1h
temperature
-196
20
80
100
120
Τ(mpa)
23.8
21.6
7.4
7.4
4.5
Useabove formulation # 2 fourteen modified Polyurethane adhesive
sesame oil polyether-modified TDI 20 (of N2O4) modified TDI 50 N220 lime-modified TDI 30 60 Glycerin 10
20°C/24h. Τ=5-7.0mpa for oil drum repair.
